Eachine Tryo109 210mm DIY 5 Inch FPV Racing Drone PNP w/ F4 30A 600mW VTX Caddx Turbo Eos2 1200TVL Camera

4.0 (Reviews 2)
US$109.00 US$115.00
US$109.00 US$115.00

Buy at


Eachine Tryo109 210mm DIY FPV Racing Drone PNP w/ F4 30A Caddx Turbo Eos2 1200TVL Camera

Notice: It is DIY Version that comes unassembled. 

Brand Name: Eachine
Model: Tyro109
Version: PNP ( Without Receiver)
Weight: 311g 

Item Specification
210mm Frame Kit
Wheel base: 210mm
Frame arm thickness: 5mm
Bottom plate thickness: 2mm
Side plate thickness: 2mm
Frame kit material: 3K carbon fiber & 6065 aluminium 
2206 2400KV Brushless Motor

KV: 2400KV
Idle current (Io/10V): 1.26A
Lipo cell: 3-5S
Weight: 31g
Max continuous current: 31A
Max continuous power: 496W
Max thrust: 1050g (4S/5")
Configu-ration: 12N/14P
Motor resistance (RM): 0.0572 Ω 
Stator diameter: 22mm
Stator thickness: 6mm
Motor diameter: 27.7mm
Motor body length: 19.2mm
Overall shaft length: 34.2mm
Prop adapter shaft: M5
Bolt holes spacing: 16mm
Bolt thread: M3
Propeller: 5-6 inch
4 IN 1 30A BLHeli_S ESC

Continuous current: 30A
Peak Current: 40A(10S)
Input voltage: 2-5S
Main control chip: 48Mhz EFM8BB2
Firmware: BLHeli_S supports Dshot600
MOS: 5*6
Customized F4 Flight Controller

Main control chip: STM32F405
Sensor: ICM20602 6-axis
Power supply: 5V
Integrated OSD
Onboard LC filter
PID cycle rate & gyro refresh rate up to 32Khz
Supports BetaFlight / inav racing firmware
Caddx Turbo Eos2 1200TVL  Camera

FOV: 160°
Lens: 2.1mm
TV System: NSTC
Latency: min 3ms
Resolution: 1200TVL
Illumination: 0.005LUX
Schutter: Rolling Schutter
Power Input: 3.3V-9V
Image Sensor: 1/3 inch COMS
Aspect Ration: 16:9 / 4:3 choosable
Net weight: 5g
Dimension: 14 * 14 * 16mm
Package weight: 41g
Package dimension: 66 * 66 * 32mm
Xf5804 5.8G 40CH 0mW/25mw/200mw/600mw switchable VTX

Output power & transmission distance: ≥[email protected], ≥[email protected], ≥[email protected]
Transmitting power: 0mW/25mW/200mW/600mW
Full video format: NTSC /PAL
Input voltage & power dissipation: 7V~24V, +12V/[email protected]
Size: 20*30*9mm
Weight: ≤7g(except antenna)
With output power self-check function.
Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
5040 5 Inch 4-Blade Propeller

Material: PC
Mounting hole: 5mm
Center thickness: 8mm
Color: blue & purple
Quantity: 4 CW + 4 CCW
Battery Not included
Recommend 3-5S

Package Included:

1 x 210mm frame kit
2 x 2206 2400KV brushless motor CW
2 x 2206 2400KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x Customized F4 flight controller
1 x Caddx Turbo Eos2 1200tvl 
1 x XF5804 5.8G 40CH 0mw/25mw/200mw/600mw switchable VTX
2 x Battery strap
4x 5040 four-blade propeller CW
4 x 5040 four-blade propeller CCW


Average rating:
4.0 / 5.0
  • 3.0
    By VRMan3D-Fred Cass

    No voltage from plug to vtx?

    Everything went together very easily and tests fine. However after I double checked everything, (with smoke stopper), I plugged it in. Everything fine but the VTX didn't light up or work. So I started testing with a multimeter and there is no battery voltage coming from the plug on the right edge of the FC. I even ended up cutting the wires to see if it was just a bad cable. Nope, there is just no voltage on the last pin/wire from the plug. I suppose I could wire it directly to the battery (I noticed it says it needs at least 7volts) This is still not a good solution because I would imagine that if the power worked on the vtx plug like it should that it would be filtered. It is a faulty FC. Should I return it to Banggood? Please help. Thanks.

  • 5.0
    By PropHawk

    Frame is tough, I'm learning fast!!!

    I bought my Tyro109 and assembled in 6 hours. We my first. After checking everything my and setting up in Betaflight I tired to fly it. The Esc glowed, smoked and was faulty. I replaced the esc and FC with Diatone Mamba stack. Had to modify canopy some but i got it to fit.. I have flown it many times and I'm learning to pilot this very fast quad on 4s. I have crashed a lot. A whole lot haha. Frame is tough. Motors are strong and are holding up well. I duo not know how to set vtx and recommend running a Jumper wire from vtx data pad to a Tx pad on your FC for smart audio or you won't be able to set power, channels or frequency once assembled. There is no instructions for vtx anywhere online. I only got one set of props also. Description says 5 sets, picture shows 2 sets. I got one set



Review Title * 0 /100

The review title can not be empty!

Review Content * 0 /800

The review content can not be empty!

Add Photo

    Max 2 images, 2MB per image, Format: jpeg/jpg/gif/png/bmp

    Add Video

    Share a video with your review, please make sure your video is related to the product


    Your review is submitted successfully!

    We will process your review within 1-5 business days.